Splunk® Enterprise

Managing Indexers and Clusters of Indexers

Acrobat logo Download manual as PDF

Splunk Enterprise version 7.0 is no longer supported as of October 23, 2019. See the Splunk Software Support Policy for details. For information about upgrading to a supported version, see How to upgrade Splunk Enterprise.
This documentation does not apply to the most recent version of Splunk® Enterprise. For documentation on the most recent version, go to the latest release.
Acrobat logo Download topic as PDF

Best practice: Forward master node data to the indexer layer

It is considered a best practice to forward all master node internal data to the indexer (peer node) layer. This has several advantages:

  • It accumulates all data in one place. This simplifies the process of managing your data: You only need to manage your indexes and data at one level, the indexer level.
  • It enables diagnostics for the master node if it goes down. The data leading up to the failure is accumulated on the indexers, where a search head can later access it.

The preferred approach is to forward the data directly to the indexers, without indexing separately on the master. You do this by configuring the master as a forwarder. These are the main steps:

1. Make sure that all necessary indexes exist on the indexers. This is normally the case, unless you have created custom indexes on the master node. Since _audit and _internal exist on indexers as well as the master, you do not need to create separate versions of those indexes to hold the corresponding master data.

2. Configure the master as a forwarder. Create an outputs.conf file on the master node that configures it for load-balanced forwarding across the set of peer nodes. You must also turn off indexing on the master, so that the master does not both retain the data locally as well as forward it to the peers.

Here is an example outputs.conf file:

# Turn off indexing on the master
index = false
defaultGroup = my_peers_nodes 
forwardedindex.filter.disable = true  
indexAndForward = false 

This example assumes that each peer node's receiving port is set to 9997.

For details on configuring outputs.conf, read "Configure forwarders with outputs.conf" in the Forwarding Data manual.

Last modified on 15 September, 2020
Enable the search head
Prepare the peers for index replication

This documentation applies to the following versions of Splunk® Enterprise: 7.0.0, 7.0.1, 7.0.2, 7.0.3, 7.0.4, 7.0.5, 7.0.6, 7.0.7, 7.0.8, 7.0.9, 7.0.10, 7.0.11, 7.0.13, 7.1.0, 7.1.1, 7.1.2, 7.1.3, 7.1.4, 7.1.5, 7.1.6, 7.1.7, 7.1.8, 7.1.9, 7.1.10, 7.2.0, 7.2.1, 7.2.2, 7.2.3, 7.2.4, 7.2.5, 7.2.6, 7.2.7, 7.2.8, 7.2.9, 7.2.10, 7.3.0, 7.3.1, 7.3.2, 7.3.3, 7.3.4, 7.3.5, 7.3.6, 7.3.7, 7.3.8, 7.3.9, 8.0.0, 8.0.1, 8.0.2, 8.0.3, 8.0.4, 8.0.5, 8.0.6, 8.0.7, 8.0.8, 8.0.9, 8.0.10

Was this documentation topic helpful?

You must be logged into splunk.com in order to post comments. Log in now.

Please try to keep this discussion focused on the content covered in this documentation topic. If you have a more general question about Splunk functionality or are experiencing a difficulty with Splunk, consider posting a question to Splunkbase Answers.

0 out of 1000 Characters