Set up Linux for workload management
Before you can configure workload management in Splunk Enterprise, you must set up cgroups on your underlying Linux operating system. How you set up cgroups
for workload management depends on whether your Linux system is running systemd. To determine if your system is running systemd
, see Is Linux running systemd?.
Workload management supports Linux cgroups v1 only. If your Linux system has been upgraded to a version running cgroups v2, you must revert your system to cgroups v1 to use Workload Management in Splunk Enterprise. For additional guidance and resources, see Workload Management operation during the transition to cgroups v2.
Is Linux running systemd?
Use one of the following options to determine if your Linux distribution is running systemd.
Option 1: Check systemd version
Run the systemctl
command to check for a systemd
version number.
$ systemctl --version systemd 219 +PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN
Workload management supports systemd
version 219 or later. See System requirements.
Option 2: Check for systemd process ID
Run the following command to check for a systemd
process ID. On most Linux systems, if the output shows PID=1, then you are running systemd
. For example:
$ pidof systemd 1
On Debian-based systems, /sbin/init
is symlinked to /lib/systemd/systemd
. As a result, the pidof
command returns a number other than 1
. For example:
$ pidof systemd 5447
To confirm that a Debian-based system is running systemd
, run the following command:
$ ps -q 1 ax PID TTY STAT TIME COMMAND 1 ? Ss 0:13 /sbin/init
The output shows a value of /sbin/init
under the COMMAND
column. Now run the following command to check if /sbin/init
is symlinked to /lib/systemd/systemd
:
$file /sbin/init /sbin/init: symbolic link to /lib/systemd/systemd
The output shows that /sbin/init
is symlinked to a file called /lib/systemd/systemd
, confirming that your system is running systemd
.
To configure cgroups
on Linux systems running systemd
, see Configure systemd distributions for workload management.
To configure cgroups
on Linux systems not running systemd
, see Configure non-systemd distributions for workload management.
System requirements | Configure Linux systems running systemd |
This documentation applies to the following versions of Splunk® Enterprise: 7.3.0, 7.3.1, 7.3.2, 7.3.3, 7.3.4, 7.3.5, 7.3.6, 7.3.7, 7.3.8, 7.3.9, 8.0.0, 8.0.1, 8.0.2, 8.0.3, 8.0.4, 8.0.5, 8.0.6, 8.0.7, 8.0.8, 8.0.9, 8.0.10, 8.1.0, 8.1.1, 8.1.2, 8.1.3, 8.1.4, 8.1.5, 8.1.6, 8.1.7, 8.1.8, 8.1.9, 8.1.10, 8.1.11, 8.1.12, 8.1.13, 8.1.14, 8.2.0, 8.2.1, 8.2.2, 8.2.3, 8.2.4, 8.2.5, 8.2.6, 8.2.7, 8.2.8, 8.2.9, 8.2.10, 8.2.11, 8.2.12, 9.0.0, 9.0.1, 9.0.2, 9.0.3, 9.0.4, 9.0.5, 9.0.6, 9.0.7, 9.0.8, 9.0.9, 9.0.10, 9.1.0, 9.1.1, 9.1.2, 9.1.3, 9.1.4, 9.1.5, 9.2.0, 9.2.1, 9.2.2, 9.3.0
Feedback submitted, thanks!